Hatches

I've been working on the side seat hatches. The first photos show where I've cut out the openings in the side compartments.















This shows one of the hatches - this is the top and bottom.













This shows the two separate pieces. The top gets hinged to the bottom and they fit into the cut outs, hopefully making watertight hatches.










Another view.

These have been time consuming to make, but will be very nice to have if they turn out right.

Inside of storage compartments, seat hatches, center board work

I coated the insides of the storage compartments with 2 coats of epoxy. I got some free marine paint from a friend and put one coat in there so it will be easier to see. I may have to sand and recoat in some places.









Here you can see the center board with a polypropylene rope on the leading edge. This was recommended by other builders. You soak the rope in epoxy and it protects the board from damage.










And I've been working on the seat hatches. I made some parts twice.











And this showed up on the doorstep, so I have not been very diligent with the boat.



I really need to order the aluminum tubing for the masts. I haven't had the money to spend so I've been holding off. I have plenty more to do now, but soon I'll need the masts to go forward.


This Saturday is the local Wooden Boat Show which I look forward to all year.

Centerboard trunk and thwarts fitted

A about a week ago I glued up the parts for the centerboard trunk. After the epoxy set up, I noticed on one end the glue line was not level, which meant the trunk sides were not square with one another. So, I took a thin kerfed saw and cut the pieces apart again, ground out the epoxy and glued them back together, making sure all was true. Then I put the centerboard back inside and it was binding a bit near the front. I sanded the centerboard where it was binding and fixed that problem. Trouble is, I don't know that I'll have enough clearance to paint the centerboard so I'll probably have to sand some more.

This is just another view of the centerboard trunk and centerboard clamped in place with the thwarts. What I did not take pictures of was the details of the trunk. There is an epoxy bushing in both the trunk sides and the centerboard. Through this runs a stainless steel pin that the board pivots on.

I have since fiberglass the trunk in place and done some other things. Now I need to take more pictures.



The scale of what is in this photo is difficult to make out. It is excrement of some sort - not mine on the floor of my shop. Looked too big to be from a bird. It was about the size of a Cheeto. I believe I have a stowaway.

Tampa, FL BRS 17 on first sail

I got an email yesterday from Dave, mentioned earlier on the blog, from Tampa, FL. He has been using his BRS with a motor only, until this week. He finished all the sailing bits and took it out sailing for the first time. Here's his account of the outing, with photos.

"We launched just south of Gandy Bridge on Tampa Bay. Winds were forecast at 10 knots from the SW and bay waters with a light chop. We were on the water by about 8:30 AM in order to miss the scattered thunderstorms. Set up was a breeze. I had the sails furled around the masts and bungeed. They were lashed down on top of the boat in two crutches placed into the mast steps. All I had to do was to unlash and step them before launch. I had my daughter motor us out of the boat launch canal (right into the wind) while I unrolled the sails, clipped on the sheets and set the sprits. Then we fell off the wind, killed the motor and were sailing.

I rigged the boat just like the plans indicate and everything worked as advertised. We had 5 people in the boat (570 lbs) and I left the 6hp/4stroke dragging in the water (tilted up would interfere with the sheets). Using the GPS we clocked our progress at around 3 knots close hauled and up to a little over 5 knots on a reach. On the way back we set up a run for the boat ramp and were able to sail wing-and-wing at about 3.5 knots then the wind kicked up and we reached 5 knots. It was very easy to manage and both my daughters caught on quickly. I didn’t spend a lot of effort with tweaking trim and balance or sail shape. I did adjust the snotter position and tension a little and it was not hard to do. We were able to sail straight up the canal, past the boat ramp (traffic) and luff up in a turning basin downwind. I released the snotter, removed the sprit, rolled up the sail and unclipped the sheets and fired up the motor to dock. I am not a good enough sailor to try to dock under sail at a busy public boat ramp – yet"















As you can see, this is not some tiny little dingy.

seat tops, rudder blade, and centerboard

This picture shows the rudder blade roughed into shape. I used my block plane to remove some material and then my Makita sander/polisher with a seven inch 36 grit disk. I'll have to clean it up a little with a lighter sander and fill some nail holes in it, but it's close to finished.








This is the centerboard roughed into shape. I took these pictures about a week ago. About two days ago, I was doing some more work on the centerboard and one of the glue joints failed (it's a lot of strips of wood glued together with epoxy). I think what went wrong was that the wood (mostly "yellow pine") drew too much of the epoxy into the wood, thereby starving the joint. I did precoat the wood with epoxy, but I did not thicken the second coat with anything.

Several of the joints failed, but some did not. I beat the laminated pieces that remained intact against my table to see if they would come apart, after I heated them with the heat gun. I beat them and beat them and beat them. The joints did not fail and there was no sign on the wood of the abuse - pretty tough stuff.

I put the pieces back together by first sanding them, second, wiping them with acetone, third, pre-coating with epoxy, and fourth, gluing with epoxy thickened with cabosil.
These next two pictures show the seat tops cut to shape. I will not glue until after my centerboard trunk and some other parts are installed. I think the boat looks good with them in though.

Seat sides, outwhales, outer stem - a lot of work!

In the past couple of weeks I've cut the seat sides to shape, joined them with butt joints, and epoxied and fiberglassed them into place. The last step, epoxying and fiberglassing, was the most time consuming. All the joints require thickened expoy - you can see there are many joints - to the transom, the bottom, the side bulkhead, the stringer between the side bulkhead and seat side, and the forward bulkhead. I failed to get a picture of the framing for the seat sides. It was not difficult to cut and fit all these pieces, but work on the rest of the pieces for the seats could not proceed until these were glued and cured.

This photo shows the outwhale and outstem dry fit. These pieces are yellow pine. I cut the gunnels out of two pieces and then scarfed them to get the full length.











The rest of the photos show the finished work. I took about 3 hours to do each seat side - just the epoxy and fiberglass work. I did one side one day and the other the next day. I am please with the results. My fiberglass and epoxy work is not flawless, but it is pretty neat.






















The outwhales and outer stem took about one hour to glue up. It was in the 90s yesterday when I did these pieces. I sweated a lot, but because the humidity was only around 55 %, it was not too bad. Which leads me to the following conclusion: I don't care what they say in Phoenix, dry heat is nowhere near as bad as humid heat! It actually felt very nice with a breeze yesterday.




It surprised me how long these steps took.

Misc.

This is the piece of wood I am planning to use for the outer stem (the very front of the boat - the part that will like hit docks and various other obstructions). It is old growth yellow pine (I hope it's longleaf, but I can't tell). It is completely saturated with sap and very dense. I have to do some research to determine if I need to treat its surface before I glue it on. I've read that with some "oily" woods like teak and white oak, you're supposed to wipe them down with some chemical before applying the epoxy in order to get a proper bond. I don't know yet about pine sap.

It's not easy to see in this photo, but the bottom of the side stringer (the lower horizontal piece) was originally flush with the bottom of the piece running horizontal across the transom. This was incorrect and so I had to partially remove it and re-glue where it lies now. Fortunately, this was not too difficult. I just chiseled it loose from the side. I did manage to rip one layer of the plywood from the port side. I think the only reason this did not happen on the starboard side is because I did not have a very good glue up there. I was glad to be able to fix this without too much trouble. Had I left it the way it was, the seat would have been too high at the stern.
This picture shows the side frames partially glued in place and how the boat looks without the temporary center frame. The plans have these as solid pieces of plywood. I cut the centers out so that I can utilize the entire length of the storage areas which run almost the length of the boat on either side. I want to be able to fit fishing rods in there.







This photo just show the pine boards I found in my shop. They are both 16' long, yellow pine. The one on the bottom is knot free and very nice. The one on the top is nice but for a few knots. Because the bottom piece is 16' by about 6", I can get all but two feet of both gunnels out of it. I will then scarf the remainder from the top piece, cutting so as to avoid the knots.